Fabric Inspection 4 Point System:Formula, Chart, and Example

Fabric Inspection 4 Point System

By Juxiang Apparel Editorial Team — Published July 31, 2026

Fabric Inspection 4 Point System is basically how mills stop small problems from becoming big ones. Think about it. A tiny hole, a smudge of oil, one broken yarn, or a random dye streak doesn’t look like a big deal at first glance. But if that roll goes straight into cutting, that same little flaw can end up repeated across hundreds of garments before anyone even notices.

And that’s where the real trouble starts. Wasted fabric. Late shipments. A buyer who’s suddenly frustrated. All because of one small thing nobody caught early enough.

That’s exactly why this system exists. It lets inspectors check the fabric roll before cutting even begins, so flaws get caught while there’s still time to actually fix them.

So how does it work? Every flaw found gets a score between 1 and 4 points, depending on how serious it is. Once you total up all the points, you convert that number into a score per 100 square yards. This way, you can fairly compare a small roll against a much bigger one.

The rule is simple. Lower points mean better fabric. Most mills treat 40 points as the cutoff, but it’s really something buyers and suppliers should agree on together.

What Is the 4 Point System?

Put simply, the 4 point system grades fabric using nothing more than a trained eye. Mills use it on woven fabric, knit fabric, grey fabric, and finished fabric.

Here’s how the process breaks down:

  • An inspector checks the fabric closely, section by section.
  • Whatever flaw turns up gets marked with a score of 1, 2, 3, or 4 points.
  • Minor flaws get low scores. Serious ones get higher scores.
  • Once inspection is done, all those points get added up.
  • That sum becomes the roll’s final score.

So why go through the trouble of converting the score? Because fabric rolls come in different lengths. Naturally, a longer roll will show more flaws just because there’s more material to look at. Turning the total into “points per 100 square yards” fixes that imbalance, letting a 50 yard roll and a 500 yard roll be judged on equal terms.

This ties directly to the ASTM D5430 test method, which lays out the process for inspecting and grading fabric. What it doesn’t do is set a single pass or fail number for everyone. That decision falls to buyers and suppliers, who settle on it together based on the fabric, the garment, and the price point at hand.

At the end of the day, fabric inspection is just one link in the full garment production process, and it works best alongside clear specs for measurements, construction, and color.

Defect Scoring Chart

Each flaw is scored by its length:

 

Flaw length  Points 
Up to 3 inches  1 point 
3 to 6 inches  2 points 
6 to 9 inches  3 points 
Over 9 inches  4 points 

No single flaw can score more than 4 points.

Holes are scored more strictly, since they carry more risk:

 

Hole size  Points 
1 inch or smaller  2 points 
Larger than 1 inch  4 points 


Two Rules to Know

There are two important rules worth knowing here.

  • One-yard cap. Many buyers set a cap of 4 points per linear yard, even if that same yard has several flaws piled up in it. Don’t just assume this applies, though. Confirm it with your buyer before actually using it.
  • Critical flaws override the score. Certain flaws lead to an automatic reject, no matter what the total score ends up being. This covers things like bad holes, full-width flaws, and severe shade shifts.

One more thing worth stressing: keep the same scoring rule throughout the entire shipment. If inspectors switch rules partway through, the scores stop being comparable, and the whole inspection loses its value.

The Formula

Here’s the formula for points per 100 square yards:

Points per 100 sq. yd. = (Total points × 36 × 100) ÷ (Width in inches × Length in yards)

(That number 36 is just there to convert inches into yards.)

And here’s the version for points per 100 square metres:

Points per 100 m² = (Total points × 100) ÷ (Width in metres × Length in metres)

One important habit: always note down which unit you used. A score calculated in square yards simply can’t be compared against a limit set in square metres.

Worked Example

Let’s walk through a sample roll:

  • Length: 120 yards
  • Width: 60 inches
  • Total points found: 28

Plugging these numbers into the formula:

(28 × 36 × 100) ÷ (60 × 120) = 100,800 ÷ 7,200 = 14

That gives us a result of 14 points per 100 square yards.

If the pass line is set at 40 points, this roll clearly passes.

Still, don’t just stop at the number itself. It’s worth checking for:

  • A critical hole
  • Bad shade variation
  • Wrong usable width
  • Too much bowing or skewing
  • Flaws sitting in key cutting areas

A good score is really just a green light. It’s not the whole story.

How to Inspect Fabric: 10 Steps

  • Check the buyer’s specs: Before starting anything, know the fabric standard, shade standard, required width, sample size, scoring rule, and pass line.
  • Pick which rolls to check: Checking 10% of rolls is fairly standard. That said, check more if the supplier is new, the fabric is expensive, or past orders have had issues.
  • Set up your space: You’ll want a clean machine, strong lighting, a tape measure, defect stickers, swatches, a report form, and a camera on hand.
  • Log the roll info: Before opening anything, write down the supplier, PO number, color, dye lot, and roll number.
  • Check width and length: Measure the width at three points along the roll, start, middle, and end. Then compare the actual length against the label.
  • Run the fabric through: Go at a pace slow enough that every flaw is clearly visible.
  • Mark every flaw: Note the type, size, and exact location on the roll. Snap a photo if it helps.
  • Score each flaw: Use the chart covered earlier, and don’t switch the rule partway through inspection.
  • Add up the total: Convert that number into points per 100 square yards or square metres.
  • Make the call: Accept it. Hold it. Use it with limits. Downgrade it. Or reject it outright.

Common Fabric Flaws

 

Type  Examples 
Weaving  Broken yarn, slub, loose thread 
Knitting  Dropped stitch, hole, needle line 
Dyeing  Streaks, patchy color, shade shift 
Printing  Blurry print, wrong color, missing print 
Finishing  Crease marks, uneven finish 
Contamination  Oil, dirt, rust, mildew 
Physical damage  Holes, cuts, tears, snags 
Size issues  Wrong width, short roll 

Some issues, like shrinkage, odor, or colorfastness, simply won’t show up through a visual check. These need an actual lab test. No matter how careful the inspection is, the point score alone just can’t catch them.

What Score Should You Accept?

40 points per 100 square yards tends to be the go-to pass line most people default to. But it’s really just a starting point, not something set in stone. Treat it that way.

 

Score  What it usually means 
0–20  Strong quality 
21–30  Usually fine 
31–40  Check against your agreed limit 
Over 40  Often held or rejected 

Where you actually set your pass line should come down to a few things: the fabric type you’re working with, the garment it’s headed for, the price point involved, and whatever critical-flaw rules you’ve already agreed on beforehand.

What Goes in an Inspection Report

A good report should let anyone reading it understand exactly what was found and why. Make sure it includes:

  • Basics: buyer, supplier, PO number, fabric type, color, dye lot, date, inspector name
  • Roll data: roll number, real vs. labeled length and width, amount checked
  • Flaw log: flaw type, size, spot on the roll, points given, photo
  • Final math: total points, area checked, final score, pass line, decision

Also, log shade shifts, bowing, and width loss separately. The point score won’t capture any of that on its own.

Common Mistakes to Avoid

  • Thinking 40 points is a fixed rule: It’s common, sure, but it isn’t required.
  • Switching scoring rules mid-shipment: Doing this breaks the whole comparison across rolls.
  • Only checking easy rolls: Sample across the full shipment, not just one convenient pallet.
  • Trusting the label over the tape measure: Always measure the width and length yourself.
  • Running the machine too fast: Speed without accuracy isn’t real quality control.
  • Trusting the score alone: A low score can still hide a bad hole or a shade shift underneath it.
  • Skipping flaw locations: A number with no location attached is useless to the cutting team.
  • Mixing dye lots: This can cause shade mismatch, even when the scores themselves look fine.

FAQs

What is the 4 point system in fabric inspection?

It grades fabric flaws one by one. Each flaw picks up somewhere between 1 and 4 points, depending on how big it is. Add them all up and you get a single score per 100 square yards or square metres.

Why is it called the 4 point system?

Because 4 is the highest score you can ever give a single flaw, no matter how bad it looks.

What is the formula?

Points per 100 sq. yd. = (Total points × 36 × 100) ÷ (Width in inches × Length in yards).

Is 40 points always the pass line?

Not always, no. It’s a common number people use, but really, the buyer and supplier need to sit down and agree on it themselves.

How many rolls should get checked?

A good starting point is usually around 10%. For orders that are high-value or considered higher-risk, it’s worth checking more than that.

Does a passing score mean the fabric is fully approved?

Not on its own. Things like shade, width, shrinkage, and how the fabric feels are usually checked as separate steps.

When should fabric get inspected?

Ideally, right when it arrives, before it ever reaches the cutting table.

Final Word

At its core, the Fabric Inspection 4 Point System is a fast, fair way to catch fabric problems before anything gets cut. It’s not a complicated system, but honestly, it only works if everyone actually sticks to it the same way, every single time. Use the right formula, and resist the urge to round numbers or skip a step just because you’re pressed for time. Keep one scoring rule running through the entire shipment from start to finish. 

The second someone switches rules midway, every score becomes meaningless, since there’s nothing left to fairly compare them against. Note down exactly where each flaw sits on the roll, not just what kind of flaw it is, because a cutting team needs that location just as much as they need the score. And before inspection ever starts, sit down with your buyer and lock in a clear pass line together, so nobody’s left arguing once the results actually come in.

Planning a new order? Send Juxiang Apparel your designs, fabric needs, and quality targets. We can help with sourcing, sampling, and OEM production for your brand.

Share:

Send Us A Message